NCCCO Advance Rigger Practice Test

Browse all practice questions for the NCCCO Advance Rigger Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Start practice testFlash cards
NCCCO Advance Rigger Practice Test course image
Check These Crucial Elements Before Operating a Mobile CraneWhat must be checked daily before operating a mobile crane?Essential Safety Tips for Operating Mobile Cranes EffectivelyWhen traveling on a rubber tire mobile crane, how should the boom be positioned?Establishing Exclusion Zones is Key to Rigging SafetyWhich of the following is a common rigging safety practice?Explore the Essential Knots Used in RiggingWhat type of knots are commonly used in rigging?How Many Parts of Line Do You Need for a Heavy Load?For a load weighing 500,000 pounds, which is the correct number of parts of line needed?How to Calculate Safety Factors in Rigging with Wire Rope SlingsWhen using a 1-inch wire rope sling in a vertical basket hitch lifting a 24-foot long, 36-inch diameter pipe, what is the safety factor?How to Calculate Sling Leg Forces When Lifting with a Bridle SlingLifting 20,000 lbs with a 2-leg bridle sling at a 30° horizontal sling angle, what is the force applied to each leg?Key Safety Measures for Crane Operations During Bad WeatherWhat is a common safety measure during crane operations in inclement weather?Learn the Best Ways to Store Your Rigging EquipmentHow should rigging equipment be stored to ensure it remains in good condition?The Importance of Lifting Loads Equally in RiggingWhat is the recommended practice when lifting loads in pairs?Understand the Formula for Snatch Block Stress in Vertical LiftsWhat formula is used to determine stress on a snatch block performing a vertical lift?Understand the Importance of Crane Inspections for SafetyHow often should cranes be inspected according to safety regulations?Understanding a critical lift in advanced rigging and why it mattersDescribe a "critical lift."Understanding Crane Safety: What to Do When Contacting Power LinesAll of the following statements about crane contact with power lines are TRUE EXCEPT:Understanding Crane Signals in Tugger Operations for Effective RiggingWhen a tugger is mounted where the operator cannot see the load, the signal person MUST use:Understanding Critical Rigging Decisions for Safety and SuccessWhat are "critical rigging decisions"?Understanding Hand Signals for Lowering a Load in Rigging OperationsWhich hand signal is indicated for lowering a load?Understanding How Riggers Can Prevent Accidents on Job SitesHow can a rigger assist in preventing accidents?Understanding Lifting Radius in Crane OperationsWhat does the term "lifting radius" refer to?Understanding Load Charts in Crane Operations for Safe LiftingWhat does the term "load chart" refer to?Understanding Load Limits in Rigging ComponentsWhat does the term "load limit" signify in rigging components?Understanding Parts of Line for Lifting 200,000 PoundsWhen lifting a load of 200,000 pounds, how many parts of line does one typically use?Understanding the Crucial Role of Lift Plans in Rigging SafetyThe methodical process that attempts to identify hazards and devise plans to overcome or eliminate hazards which may interfere with crane or rigging is called?Understanding the Essential Characteristics for Rigging LoadsWhich characteristic is essential for a load being lifted by a rigging component?Understanding the Essential Purpose of a Lift PlanWhat is the primary purpose of a lift plan?Understanding the Essential Safety Factors for Lifting SlingsWhat is the recommended safety factor for lifting slings?Understanding the Essentials of a Rigging PlanWhat is a rigging plan?Understanding the Immediate Steps to Take When an Injury Occurs During RiggingWhat should be the first response if someone is injured during a rigging operation?Understanding the Importance of Effective Communication in Rigging OperationsWhy is effective communication essential during rigging operations?Understanding the Importance of Pre-Rigging Inspection for Safe LiftingWhat is the primary purpose of a pre-rigging inspection?Understanding the Importance of Proper Training in Rigging OperationsWhy is proper training crucial for individuals involved in rigging operations?Understanding the Key Differences Between Choke Hitches and Loop HitchesWhat is the difference between a choke hitch and a loop hitch?Understanding the Key Responsibilities of an Advanced RiggerWhat is one key responsibility of an advanced rigger?Understanding the Legal Requirements for Rigging Gear CertificationWhat is the legal requirement for rigging gear before use?Understanding the Operator Signal to Travel Both TracksWhat is the proper response when the operator gives a signal to "Travel (both tracks)"?Understanding the Purpose of a Tag Line in Lifting OperationsWhich of the following describes the purpose of a tag line during a lift?Understanding the Risks of Damaged Rigging HardwareWhat is the risk of using damaged rigging hardware?Understanding the Risks of Using Degraded Rigging HardwareWhat is the primary risk of using degraded rigging hardware?Understanding the Role of Hook Angle in Lifting OperationsWhat is the significance of the hook angle when lifting?Understanding the Weight of the Load is Key to Safe Lifting OperationsThe MOST important information to consider when planning a lift is:Understanding When Loads Are Considered Overloaded in Rigging SafetyWhen is a load considered “overloaded” in terms of safety regulations?Understanding When to Remove Chain Slings from ServiceAt what percentage of increase in length should a chain sling be removed from service?Understanding Why Some Factors Don’t Stop Personnel Lifting OperationsWhat are the reasons for stopping personnel lifting operations, EXCEPT?What happens when rigging gear is overloaded and why it’s dangerous in lifting operations?What is one consequence of overloading rigging equipment?Why backward stability is the key concern when operating at high crane boom anglesWhat is the PRIMARY concern when working with high boom angles?Why Coordination and Communication Matter in Rigger LiftsWhat must always be considered when planning a lift involving multiple riggers?Why removing damaged rigging components is essential for safetyWhy is it important to remove a damaged rigging component from service immediately?Why Signal Persons Are Essential for Safe Hoisting OperationsThe only personnel allowed to have their body parts outside of the suspended personnel platform during hoisting and lowering operations are:
More practice questions

These questions are part of the practice quiz. Start practicing

  • Which force is required to move an object up an inclined plane compared to lifting it vertically?
  • What are lifting lugs?
  • Which standard governs rigging practices in the United States?
  • What is a "rigging inspection checklist"?
  • Anchorage points for fall arrest for a single person MUST be able to hold:
  • Which hand signal indicates the operator should "Hoist"?
  • What is the role of a rigger in ensuring load placement?
  • When using a wedge socket, how is the dead end of the rope secured in the socket?
  • What is the most important reason rigging hardware should NOT be modified?
  • What is the significance of a "spotter" in rigging operations?
  • What provides additional control of a load being lifted?
  • What are the color codes on lifting slings used for?
  • When working in close quarters, what should be the main concern?
  • In an emergency situation, what is the rigger's FIRST priority?
  • What should always be done before starting a lift with any rigging equipment?
  • For a load weighing 265,000 pounds, how many parts of line are needed according to the chart?
  • In the context of rigging, what does the term 'SWL' stand for?
  • Personnel platforms shall NOT be used to lift what?
  • Why is it important to inspect rigging equipment before use?
  • Two cranes are lifting 100 tons. If crane A has 40% of the load, how much weight will crane B have on its hook?
  • To CONFIRM the rated capacity of a specific sling, consult the manufacturer's:
  • A one-inch, 3-leg bridle wire rope sling, rigged at a 45° angle, has a capacity of 18 tons. What happens with the addition of a fourth leg?
  • What is required if there is a deviation from the lift plan?
  • How frequently should rigging equipment be inspected?
  • What is the difference between static and dynamic lifting?
  • What is the primary goal of the NCCCO's certification program?
  • What type of plan is often required for lifts exceeding a certain weight threshold?
  • The primary purpose of an equalizer beam in a lift operation is to:
  • How can environmental factors affect rigging operations?
  • What is a common indicator of proper rigging practices?
  • Why is communication essential among riggers during a lift?
  • Which of the following is NOT a common type of rigging hardware?
  • What is the standard hand signal for "Stop"?
  • In rigging, what does "saturation" refer to?
  • In a typical load distribution scenario, the center of gravity must be located within which area?
  • What is an important factor when selecting rigging equipment?
  • How many parts of line are necessary for a load of 150,000 pounds?
  • Most cranes in duty cycle operation require a:
  • During a rigging operation, who is ultimately responsible for the safety of the load maneuvering?
  • Which of the following must be monitored while operating rigging in adverse weather conditions?
  • Which term best describes a method for determining the center of gravity in a load?
  • Before performing pick and carry operations with any mobile crane, it is important to:
  • The primary function of a tagline during lifting operations is to:
  • What should the operator do if weather conditions become dangerous while lifting personnel?
  • What materials are commonly used to make rigging slings?
  • What must be considered when calculating load weight for a lift?
  • Which of the following items are used for heavy rigging?
  • What action should a crane operator take if both fists are in front with thumbs out?
  • What might be a consequence of improper rigging practices?
  • What should be done with a damaged rigging component?
  • What does the term "overloading" refer to in rigging?
  • Where should the location of electrical hazards on the job site be documented?
  • According to ASME B30.5, a two crane lift is signaled by:
  • What is critical to ensure when performing a lift with multiple cranes?
  • What is the responsibility of the crane operator in a rigging operation?
  • What is the primary focus of a site analysis?
  • What does the term "reeving" refer to in the context of rigging?
  • What feature makes synthetic slings particularly advantageous for riggers?
  • Why is it essential to consider wind conditions during rigging?
  • If the jacket of a synthetic round sling is damaged, what should be done with that sling?
  • Which equipment is most commonly used for lifting heavy loads?
  • During a lift, what is the primary consideration for riggers to ensure safety?
  • What is a common definition of "block and tackle" in rigging?
  • On multiple crane lifts, the load on each crane should NOT exceed what percentage of capacity?
  • Which of the following is a safety requirement for rigging operations?
  • Describe the characteristics of properly sized rigging equipment.
  • What must be determined first to calculate the formula for block load?
  • OSHA regulations require hook replacement if the opening exceeds what percentage of its original throat opening?
  • What do we call the loads introduced into the machine or its components due to accelerating or decelerating force?
  • When materials are being hoisted to an upper level, a tag line is used to:
  • What is the primary purpose of a rigger in construction?
  • In the term (D/d ratio) the d is an abbreviation for:
  • What is the purpose of a tagline in rigging?
  • During a lift, the rigger observes a weak point in the rigging setup. What is the best action to take?
  • What is the purpose of a "ground guide" in a rigging operation?
  • Explain the term "rigging hardware."
  • What is the minimum clearance required for a crane operating near a 250 kV energized power line?
  • When determining a rigging method, which factor is NOT typically considered?
  • What type of environment requires special considerations when rigging?
  • Before a spreader bar or beams can be used they MUST have been:
  • What does "load movement" refer to in rigging?
  • What is one key benefit of using synthetic slings over wire rope slings?
  • What is meant by the term "two blocking"?
  • How is load weight calculated when lifting an object?
  • What is the maximum percent of rated capacity that can be used to lift personnel?
  • What should the operator ensure before lifting any load?
  • How do you determine the weight of a load to be lifted?
  • Which of the following is NOT a factor when making submerged lifts?
  • According to standard rigging practices, what should be the first step after identifying a potentially hazardous condition?
  • What should be used to control the movement of a swing-away lattice extension when erecting or stowing it?
  • What standard hand signal is used to communicate "Use whip line"?
  • What factors should be accounted for when positioning a crane for a lift?
  • What is the main purpose of tag lines during a lift?
  • What action should be taken if a rigging operation cannot be performed safely?
  • Define "center of gravity" in the context of rigging.
  • The point of any object's weight can be assumed to be concentrated at which location?
  • Why is it important to use the correct sling length in a rigging operation?
  • What is a "picking point"?
  • In multiple crane lifts using an equalizer beam, the weight of the beam should be considered:
  • Prior to use, all new, altered, modified, or repaired rigging hardware shall be inspected by whom?
  • Which type of sling is generally stronger?
  • On level ground using skids and rollers, what percent of the weight of the load should yield the required line pull as a general rule of thumb?
  • Which action is recommended if a load begins to swing?
  • Proper lead sheave placement as it relates to the hoisting drum location is:
  • An unsafe condition that riggers should be aware of when dealing with a multi part load block is:
  • All of the following are results of unbalanced reeving of the hook block EXCEPT:
  • A document that outlines weights, crane configuration and rigging requirements for a lift is called a:
  • During which condition does lightning present the greatest hazard to crane operations?
  • What is the primary function of a turning block in rigging?
  • How can you verify if a load is balanced before lifting?
  • When forming a lift plan, what is the PRIMARY concern for the person doing the rigging?
  • What should be done if the ground conditions are not suitable for hoisting operations?
  • What does LMI stand for?
  • All of the following conditions exert dynamic loading on a crane EXCEPT:
  • What general principle governs the safe lifting of loads in crane operations?
  • Who can design a personnel platform?
  • What is the function of a tag line in rigging operations?
  • When using a tag line, it is primarily intended to:
  • How do you properly determine the load angle?
  • Using the sling chart, what is the rated capacity of a ½ inch sling in a basket hitch with sling legs at 90 degrees?
  • Which standard hand signal indicates "Travel (one track)"?
  • What does the load factor represent in rigging?
  • Describe the term "dynamic load."
  • Planning for rigging is required:
  • In a spur-gear chain hoist with a two-chain system, what is the endless chain primarily used for?
  • Why is it crucial to confirm the suitability of anchorage points in rigging?
  • What is the primary purpose of using a tag line during lifting operations?
  • A lift plan MUST be completed by a:
  • Which are considered exceptions to standard lift protocols?
  • When lifting 100,000 pounds, how many parts of line should the main load block be reeved with?
  • Which of the following is crucial for ensuring safety during a lift?
  • What must be confirmed during a pre-rigging inspection?
  • After any structural repair or modification, a personnel lifting platform shall be tested to what percentage of the platform rating?
Subscribe

Get the latest from Examzify

You can unsubscribe at any time. Read our privacy policy